HYDRA Carbon Dioxide Absorber
Unique Design with Base Mounted Canister
The OES HYDRA carbon dioxide absorber has a unique absorbent canister which is attached to the underside by two toggle clamps for easy removal and replacement, any liquid from breathing circuit condensation is retained in the bottom of the canister preventing contamination and allowing easy disposal.
The absorber has a bypass valve, which allows the canister to be removed in the off mode without loss of fresh gas flow during absorbent replacement.
The on / off knob and the bag / vent knob are mounted at either end of the absorber with the adjustable pressure relief mounted on the top together with an ergonomic swivelling bag connection arm allowing ease of use.
The ventilator, fresh gas and exhaust connection are all mounted on the rear of the absorber.
The complete absorber (excluding the manometer) is autoclavable.
Absorber on / off knob with canister bypass in the off position for absorbent replacement *
Quick release manometer –20 to 100 cm H20 *
Ergonomic swivel bag mount arm
Patient connections 22 mm male taper with 15 mm female taper
Ventilator connection 22 mm male taper with 15 mm female taper *
Fresh gas inlet 1.5 metre hose with 22 mm female taper
Exhaust taper 30 mm male
Ventilator / bag selection valve *
* High specification model only
|Width – Low specification model||270 mm|
|– High specification model||303 mm|
|Weight – Low specification model||7.0 kg|
|– High specification model||9.1 kg|
Mounting system 25.4 mm (1 inch) diameter hole with clamp screw.
Absorber leak rate Less than 25 cc fresh gas flow at 30 cm H2O
Canister capacity 1.4 kg (1600 ml)
Resistance of the soda lime is 1 cm H2O (0.1 kPa) at 60 litres per minute.
|Absorber complete – high spec version||9075-001||Non-return valve cover||6675-004|
|Absorber complete – low spec version||9075-005||Non-return valve cover ‘o’ seal||1230-342|
|Absorber arm assembly||9075-004||Canister assembly||8075-003|
|Manometer assembly||8075-009||Complete disposable basic breathing system||1300-039|
|Fresh gas hose assembly||9075-003||Patient filter||1300-040|
|Non-return valve||6675-003||Absorber filter||1300-041|
Anaesthesia Flowmeter Bank
Cost Effective Machine Upgrading
The OES Anaesthesia Machine Flowmeter Banks have been designed to be suitable for upgrading both old machines and for a new build.
All flowmeters are supplied fully calibrated and testing requiring only mounting and connecting to the gas supply.
The flowmeters are available with 2, 3, and 4 gases and come with a mechanical anti hypoxic device as standard.
A low oxygen pressure audible alarm with integrated reservoir and a nitrous oxide cut off can also be fitted.
The flowtubes are mounted close the the tube window giving a greater view angle.
The unique design of the blow needles provide long life with a minimum bobbin bounce.
The outlet from the flowmeter can be connected directly to a vaporizer backbar and common gas outlet or to an end block for ease of piping.
Alternatively a cagemount taper can be attached to provide vaporizer connection.
Length and diameter indexed flowtubes
Cascade tubes on oxygen and nitrous oxide
Mechanical anti hypoxic device
Flowmeter on / off switch
200cc minimum oxygen flow rate
Colour and touch coded knobs to suit individual markets
Audible alarm for oxygen failure
Nitrous oxide cut off with oxygen failure… Complete oxygen failure allows the continuous use of air on 3 & 4 gas flowmeters
Flow knob stops for off and maximum flow rates preventing damage to needles
Vaporizer backbar mounting block
Integrated secondary regulators
Selectatec® is a registered trademark of Datex Ohmeda. Plugin® is a registered trademark of Drager
|9150 – 020||2 Gas Flowmeter – O2 Lefthand|
|9150 – 021||3 Gas Flowmeter – O2 Lefthand|
|9150 – 022||4 Gas Flowmeter – O2 Lefthand|
|9150 – 001||2 Gas Flowmeter – O2 Righthand|
|9150 – 002||3 Gas Flowmeter – O2 Righthand|
|9150 – 003||4 Gas Flowmeter – O2 Righthand|
|8150 – 040||Low Oxygen Audible Alarm|
|8150 – 001||Nitrous Oxide Cut Off 2 Gas|
|8150 – 002||Nitrous Oxide Cut Off 3 Gas|
|8150 – 003||Nitrous Oxide Cut Off 4 Gas|
|8000 – 004||Common Gas Outlet with Oxygen Flush and System Pressure Relief|
|9000 – 033||Single Station Selctatec® Style Backbar|
|9000 – 034||Two Station Selctatec® Style Backbar|
|9000 – 035||Three Station Selctatec® Style Backbar|
|9000 – 040||Drager Plugin ® Backbar|
|3000 – 028||Righthand Backbar End Block – Back Entry|
|3000 – 005||Righthand Backbar End Block – Bottom Entry|
|7000 – 003||Cagemount Taper – Female|